Real nice Anest Iwata Oil Free Smart Air Compressor, model SLP-22ED Serial # GH0006, with integral hollow fiber membrane air dryer plus a Hitachi 25 gallon (approx.) storage tank. Caution compressor electrical requirement are 50 Hz 2.2kW 8.8 SCFM
Nice 3-station chemical mixing and dose skid. Includes 3 conical tanks with electrically driven agitators, 3 electrically driven adjustable metering/dose pumps, five electrically driven peristaltic pumps. All mounted to a painted black carbon tube steel frame. 3 ASCO solenoids are include for make-up water shut off. Unit operated as designed until removed from service and stored indoors approx 7 years ago. Note: peristaltic pump enclosure has a broken mounting tab.
Quantity = 144 G & H SATT Control Tops for Mix-Proof valves, rising stem design and dual 24 VDC solenoids, some tops are for single seat valves. Condition is fair
Alga SDI Air/Gas Mixing Station Power XP Explosion Proof, Model XPV 28-5 Twin Cylinder, Serial Numbers 0100252-1 & 0100252-2, Venturi Mixing Capacity = 14.0 MMBTU / HR, MAWP Vaporizer = 250 PSIG, Receiver = 50 PSIG, Vaporizer Model XP160S, 480 VAC, 48 AMPS, 40 KW, Class 1, Division 1 Group D, Enclosure. Unit was installed in 1999 but ran less than 5 hours for testing only, excellent condition
All B-Fly Valves are Red Epoxy Coated, most all need new elastomers & handles. Some valves need Stems and discs. 6 ea. 6" lug mounted B-Fly with manual handles 1 ea. 6" Wafer mounted B-Fly with gear operated handle 1 ea. 3" Lug mounted B-Fly with manual handle 3 ea. 2" lug mounted B-Fly with manual handles 1 ea. 8" Wafer mounted B-Fly with manual handle 2 ea. 3" Wafer mounted B-Fly with electric actuator and manual over-ride 1 ea. 3" Through Hole Mounted 3-Way Ball with electric actuator and manual over-ride 1 ea. 4" Lug mounted B-Fly with electric actuator and manual over-ride 1 ea. 4" Lug mounted B-Fly (not a Bray) with electric actuator and manual over-ride 1 ea. 3" Through Hole mounted 2-piece cast iron ball valve (very heavy duty)
Stand Alone Ice Water Chiller, not much information available on the unit, it has two fans, a side inlet updraft air flow configuration. Includes a SAG model FQS - W12G outlet electric solenoid valve at 1" diameter. Cost = $ 150 or best offer
Stand alone refrigeration skid to make approx. 60 GPM of chilled water for wort cooling, includes: Bitzer R22 Compressor & Coil Grundfos Dual Centrifugal Transfer Pumps Falling Film Plate HXC's ( x 6) HDPE bulk storage tank hafner (Kalte +Kilmatechnik) controls * Have the wort cooler also
Krones Fill Height Detector, came from a 700 BPM production bottle line, 230 VAC, good condition. Gamma Series Krones Flexi-Push Rejector station Cost = 6,000.00
Optima 5300 DV Optical Emission Spectrometer (not currently working) part number N0770496, Serial # 077N4091802. Includes a bunch of brand new spare parts. Amazing condition other than the software which needs to be upgraded. This unit was removed from service in 2015 and has been sitting in a climate controlled warehouse since. If you have one of these Mass Spec's then you need this for parts. I can provide pictures of all the spare parts but there are to many to submit to ProBrewer.
Reverse Osmosis Skid, Model 43CH-SR8000ECN, Serial # 88-L216554A, 5HP, 3450 RPM, 208/230/460 3 phase, Tonkaflo Pump Model SB1832G-12400, Permeate Rate @ 77°F = 5.5GPM, Concentrate Rate = 5.8 GPM, Pressure Max. = 500 PSI Final, Primary Pressure Min. = 300 PSI Final. Overall good condition, needs a deep clean and some electrical love.
Slightly used centrifugal pump, TACO Model FE2508E201F2LOA, 7.5 HP, 1760 RPM, 230/460 VAC, 8.45 Impeller Diameter, 150 # flat faced ANSI Flanged ports, 3" inlet x 2-1/2" outlet, heavy duty angle iron frame with industrial green paint.
Great running condition Prodeva, Inc. Aluminum Can Crusher, Model 165, Serial # 12911, 115 VAC, single phase 1/3 HP. System Includes: Inlet Hopper Incline Conveyor with perforated SST full length guard New conveyor drive motor and gearbox Crusher outlet "boot"
Insulated SST Cold Water Storage and Transfer Skid, Square SST Storage Tank with Point Level Controller, Dual Transfer Pumps, Insulated SST Suction and Discharge Piping all mounted to a SST angle iron frame with adjustable feet. Note: motors are wired for 50 hertz
371 Gallon single wall bulk ambient water tank, with Hitachi Neuro Jr Water Ace chiller package with single pass cooling, on-board in-line sanitary strainer, all stainless steel sch. pipe manifolds included with associated butterfly valves. Tank, Chiller, Strainer and related piping mounted to a SST angle iron frame with adjustable feet. Note: tank head space is badly rusted and will need mechanical polishing and a strong acid wash to get it anywhere near good. Might be best to replace the top head. Other components are in really good shape. Caution: the unit requires 50 Hrtz power.
Insulated SST Hot Water Storage and Transfer Skid, Square SST Bulk Storage Tank. Dual Transfer Pumps, Point Level Controller, Insulated SST Suction and Transfer Piping, all mounted to a SST angle iron frame with adjustable feet. Note: transfer pumps exhibit a lot of external rust Pump Motors require 50 hertz power
Labeller Center Pivot, New Old Stock (NOS), still in the original packaging. Minor rust that can easily be cleaned
Quantity of two (2) New Old Stock (NOS) Krones Labelers with Glue Pumps. Never installed still bolted to their original shipping pallet and one is still wrapped in the factory applied wrapping. There is nothing wrong with these units, they are as advertised brand new! Cost = $ 7,995.00 Each or both for $ 14,500.00
Krones Solomodul Labeller Parts, New Old Stock 95% still in the original wrappers and crate. These spare parts fit serial number 406-046 & 406-047 labelers. Must take all, no separate sales! Complete inventory list available upon request with quantity, description, and Krones Part numbers
Clean Out Of Place Tank, really big. Polished and Radius on all welds and angles (inside and out), lid is heavy and is missing the gas cylinders to hold it open, removable screened trough in the bottom (full length), square stainless tube steel frame with adjustable feet and pump mount pad (pump not included), spray bar on both of the long vertical sides and another spray wand mounted in the lid, lid wand has removable spray nozzles. Dimensions = 66" long x 33" wide x 36" deep Ports = Upper Straight Sidewall "midway" (inlet) 2" Tri-clamp with 90° Turn Down, Straight Side Spray Wand (x2) 1-1/2" Tri-clamp with through holes penetrating into the tank wet side, Tank Top Hinged Lid spray wand 1-1/2" Tri-clamp with removable threaded spray nozzles, Bottom side of trough (outlet) 1-1/2" Tri-clamp fit with Definox Tri-clamped B-Fly valve, Bottom of trough (drain) 2" Tri-clamp. Excellent Condition...